The Wiki for Tale 7 is in read-only mode and is available for archival and reference purposes only. Please visit the current Tale 11 Wiki in the meantime.

If you have any issues with this Wiki, please post in #wiki-editing on Discord or contact Brad in-game.

Jaylenaeybarre's gearbox guide

From ATITD7
Revision as of 15:19, 13 September 2015 by Jaylena (talk | contribs) (Created page with "I've struggled a lot with the making of gearboxes. I did find a guide from T3 (http://www.atitd.org/wiki/tale3/Users/EldradUlthran/Gearbox_Guide) and some explanations here: http...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigationJump to search

I've struggled a lot with the making of gearboxes. I did find a guide from T3 (http://www.atitd.org/wiki/tale3/Users/EldradUlthran/Gearbox_Guide) and some explanations here: http://www.atitd.org/wiki/tale6/Gearbox_Design_Guide and http://www.atitd.org/wiki/tale6/Gearbox.

Still I kept having problems and mostly tried them on a trial/error basis, which most of the times got me frustated :) so eventually, when I did manage to make them, I tried to write this guide.

Step 1 - What do you need


Step 2 - Different gearpairs

  • spacer, used to start a new layer (no cost) - to represent it in the photo's I use: 1 ::[IMG]91mpu0.jpg[/IMG]
  • one step (photo) 3/3 only allows to move in a +-shape (cost=small gears):: [IMG]2u6jmhk.jpg[/IMG]
  • diagonal (photo) 4/4 cheap :: [IMG]jqqbkg.jpg[/IMG]
  • 3/5, 5/3 makes a large change in ratio)(cost= medium gears):: [IMG]2lc9tz6.jpg[/IMG]
  • two steps up or sideways 5/6, 6/5, 4/7, 7/4 (makes smaller changes in ratio)(cost when using 7gear: large gears) :: [IMG]90btw2.jpg[/IMG]
  • knight's move 6/6, 5/7, 7/5 ::[IMG]a4ape.jpg[/IMG]]
    • 4/4 is much cheaper then 6/6 , although with 6/6 you move over large distances
    • 3/3, 4/4, 6/6 makes no change in ratio (photo still to come)
    • 3/5, 5/6, 4/7 makes the ratio go down :: [IMG]35bcl7l.jpg[/IMG]
    • 5/3, 6/5, 7/4, 7/5 makes the ratio go up :: [IMG]2r545tw.jpg[/IMG]

Step 3 - Useful to know

  • you always start at 1A, ratio 100ù
  • 8 rows, 8 columns
  • you always need to end at row 8
  • only 30 shafts can be used - = including spacers
  • no more then 3 layers/levels are possible
  • always put the smallest gear on the bottom, ex: spacer, 3-gear, 5-gear on top of each other, not spacer, 5-gear, 3-gear - it seems it is possible to put a small gear on top of a large gear, but depending on your next move, you can get the message that they are too close to each other: see photo's

[IMG]2mwxlwy.jpg[/IMG]

[IMG]2z87w9y.jpg[/IMG]

  • only 3/3, 4/4, 3/5, 5/3, 5/6, 6/5, 6/6, 4/7, 7/4, 5/7, 7/5 pairs can be used

Step 4 - Example of a 1-output gearbox

[IMG]nv3w9w.jpg[/IMG]

    • photo's from the board using the cheap 4/4 gears

[IMG]2m3ic8o.jpg[/IMG] [IMG]a2671j.jpg[/IMG] [IMG]2wbydmt.jpg[/IMG]

    • photo's from the board using the expensive 6/6 gears - but since we need to make: D160-175 we have to put some 4-gears under the 6-gears

[IMG]4v5x89.jpg[/IMG]

Step 5 - Example of a 2-output gearbox

[IMG]25q9cgh.jpg[/IMG] [IMG]qxui5l.jpg[/IMG]


    • photo's from the board; with use of the ratio's - yellow square


[IMG]2md52td.jpg[/IMG]

Step 6 - Example of a 3-output gearbox

    • [IMG]rwup7b.jpg[/IMG]


    • [IMG]nz10kx.jpg[/IMG]

Step 7 - Final

  • you'll get a message if your gearbox is not good
    • either your gears don't mesh :: [IMG]ehkj1u.jpg[/IMG]
    • either you don't have an output in row 8 :: [IMG]14txqf.jpg[/IMG]
    • either you have used up your 30 shafts
  • also on top of your board you'll see if your gearbox has the correct ratio
  • when your gearbox is ok, then you'll get a popup window: "do you want to make this gearbox .....?"



I hope this guide makes making gearboxes a bit more easier.